AMTA Paper Archive


Welcome to the AMTA paper archive. Select a category, publication date or search by author.

(Note: Papers will always be listed by categories.  To see ALL of the papers meeting your search criteria select the "AMTA Paper Archive" category after performing your search.)


Search AMTA Paper Archive
    
    




Sort By:  Date Added   Publication Date   Title   Author

Pattern

Antenna Pattern Analysis and Correction Using Higher-Order Derivatives
P. Kolesnikoff (Ball Aerospace), November 2003

Occasionally, antenna patterns have discontinuities or “glitches” in them. While most of these glitches are obvious to a human looking at the plot, it can be difficult for a computer to automatically identify glitches while ignoring sidelobes and other real features of the antenna pattern. This paper will present a technique for accurately identifying and removing antenna pattern glitches through the use of higher order derivative information.

Estimating the Uncertainties Due to Position Errors in Spherical Near-Field Measurements
A.C. Newell (Nearfield Systems Inc.), November 2003

Probe position errors, specifically the uncertainty in the theta and phi position of the probe on the measurement sphere, are one of the sources of error in the calculated far-field and hologram patterns derived from spherical near-field measurements. Until recently, we have relied on analytical results for planar position errors to provide a guideline for specifying the required accuracy of a spherical measurement system. This guideline is that the angular error should not result in translation along the arc of the minimum sphere of more than ?/100. As a result of recent simulation and analysis, expressions have been derived that relate more specifically to spherical near-field measurements. Using the dimensions of the Antenna Under Test (AUT), its directivity, the radius of the sphere (the minimum sphere) enclosing all radiating surfaces and the frequency we can estimate the errors that will result from a given position error. These results can be used to specify and design a measurement system for a desired level of accuracy and to estimate the measurement uncertainty in a measurement system.

Determining Direction of Arrival of Multiple Reflections From Measured Antenna Patterns
D.E. Warren (Air Force Research Laboratory),J. Woods (Air Force Research Laboratory), November 2003

The direction of arrival of multiple coherent electromagnetic signals can be determined by measuring the pattern of an antenna probe when it is rotated off its phase center and then exciting a synthetic array with the same geometry as the probe measurement points using the signals received in the measurement. The offset and angle of sweep, which defines the aperture size required for separating the waves, depends upon the resolution required. The sampling resolution must also fall within the Nyquist sampling criteria.

Wireless Test Cell Design Considerations
C.W. Sirles,A.R. Howland, M.H. Sewell, November 2003

This paper describes a family of new measurement systems, termed “test cells”, designed to satisfy the certification requirements of the Cellular Telephone & Internet Association’s (CTIA) “Method of Measurement for Radiated RF Power and Receiver Performance” test plan for wireless subscriber stations. These test cells employ simultaneous dual-axis mechanical scanning and operate in both far-field and near-field modes over the 750MHz to 6 GHz frequency range. Operation can be extended to higher frequencies through the use of suitable sampling antennas. Test cell facility configuration is detailed. Scanner layout and RF sampling antenna designs are discussed. Anechoic chamber characterization data is presented along with typical measured pattern and efficiency data for both broadbeam and directive AUT’s. Measurement test times for various test scenarios are discussed.

The Surface Standard Deviation Method for TRP Measurement Uncertainty
M.D. Foegelle (ETS-Lindgren), November 2003

The Cellular Telecommunication and Internet Association has developed a ripple test measurement for qualifying the quiet zone of wireless pattern measurement systems for their Mobile Station Over the Air Test Plan. The data produced by this ripple test provides a very thorough characterization of the worst possible contributions to an antenna pattern measurement performed on the qualified system. However, the characterization represented by the maximum ripple significantly overestimates the ripple seen on typical pattern measurements produced by the qualified system, and greatly overestimates the actual uncertainty involved in the determination of integral quantities such as Total Radiated Power (TRP). In order to better account for the results of this test, a statistical analysis method referred to as the Surface Standard Deviation (SSD) has been developed to determine an expected uncertainty for surface integral quantities. This paper will present the background and formulation of the SSD method and show some typical results.

A Novel Structure for Accurate Measurement of Antennas Mounted on Ground Planes
I.J. Gupta (The Ohio State University),J-F Lee (The Ohio State University), R.C. Flippo (Los Angeles Air Force Base), W.D. Burnside (The Ohio State University), November 2003

A novel structure for accurate measurements of antennas mounted on an infinite ground plane has been designed and built. The structure is eight feet in diameter and can be used to measure antennas as big as fourteen inches at the base at frequencies as low as 1 GHz. The structure is defined by blending a planar surface with an elliptical surface such that near the antenna under test the surface resembles a planar surface and then it slowly rolls back to minimize any diffractions due to discontinuities in the surface. Patterns of a few antennas mounted on the structure are presented and compared with the expected patterns of the antennas mounted on an infinite ground plane.

Implanted Antennas Inside a Human Body: Characterization and Performance Evaluation
J. Kim (University of California, Los Angeles),Y. Rahmat-Samii (University of California, Los Angeles), November 2003

In this paper, the electromagnetic (EM) characteristics of various antennas implanted in both the human head and the human body are analyzed for biomedical applications such as hyperthermia and biotelemetry. The implanted antennas are studied in two ways: the near- and far-field patterns of the antenna are calculated and the potential effects on the human body are observed. To ensure the correctness of the results, we apply two simulation methodologies: dyadic Green’s function (DGF) expansions and finite difference time domain (FDTD). We characterize the performances of the low profile antennas designed for biomedical applications in terms of specific absorption rate (SAR), radiation patterns, maximum available power and safety issues. These results should also provide a good basis for validating the results of experimental data.

Antenna Pattern Correction for Near Field-to-Far Field RCS Transformation of 1-D Linear SAR Measurements
I.J. LaHaie (General Dynamics Advanced Informations Systems),S.A. Rice (General Dynamics Advanced Informations Systems), November 2003

In a previous AMTA paper [1], we presented a firstprinciples algorithm called wavenumber migration (WM) for estimating a target’s far-field RCS and/or far-field images from extreme near-field linear (1-D) or planar (2-D) SAR measurements, such as those collected for flight-line diagnostics of aircraft signatures. However, the algorithm assumes the radar antenna has a uniform, isotropic pattern on both transmit and receive. In this paper, we describe a modification to the (1-D) linear SAR WM algorithm that compensates for nonuniform antenna pattern effects. We also introduce two variants to the algorithm that eliminate certain computational steps and lead to more efficient implementations. The effectiveness of the pattern compensation is demonstrated for all three versions of the algorithm in both the RCS and the image domains using simulated data from arrays of simple point scatterers.

Characterization of a Fresnel Zone Antenna Using Bi-Polar Planar Near-Field Measurements
N.P. Sakungew (University of California, Los Angeles),Y. Rahmat-Samii (University of California, Los Angeles), November 2003

A fully-functional Fresnel Zone (FZ) antenna was designed and measured using PO simulation programs and the bi-polar near-field facility. The results from these measurements and simulation are presented in this paper. First, a detailed description of an FZ antenna and its operation is given. Then, a discussion of the design and construction procedure for both the FZ antenna and supporting structure is included. The resulting far-field pattern, near-field plots, and holographic images are shown in this paper. The antenna was measured with different feed positions to observe how it affects the overall antenna performance.

Antenna Pattern Comparison Between and Outdoor Cylindrical Near-Field Test Facility and an Indoor Spherical Near-Field Antenna Test Facility
J. Fordham (MI Technologies),M. Scott (Alenia Marconi Systems), November 2003

A new spherical near-field probe positioning device has been designed and constructed consisting of a large 5.0 meter fixed arc. This arc has been installed in a near-field test facility located at Alenia Marconi Systems on the Isle of Wight, UK. As part of the nearfield qualification, testing was performed on a ground based radar antenna. The resultant patterns were compared against measurements collected on the same antenna on a large outdoor cylindrical near-field test facility also located on the Isle of Wight [1]. These measurements included multiple frequency measurements and multiple pattern comparisons. This paper summarizes the results obtained as part of the measurement program and includes discussions on the error budgets for the two ranges along with a discussion on the mutual error budget between the two ranges.

Wideband Optically Multiplexed Beamformer Architecture (WOMBAt) Transmit Mode
R.D. Davis (Naval Surface Warfare Center),K. Thompson (Naval Surface Warfare Center), P. Couper (Technology Service Corporation), T. Closser (Naval Surface Warfare Center), November 2003

A Wideband Optically Multiplexed Beamformer Architecture (WOMBAt) was developed and characterized at the Crane Naval Surface Warfare Center Active Array Measurement Test Bed (AAMTB) facility. The project includes development and integration of the true-time delay (TTD) WOMBAt photonic beamformer with the Active Array Measurement Test Vehicle (AAMTV). The AAMTV is a 64-channel transmit-receive (TR) module based phased array beamformer that is integrated with the AAMTB facility 12’x9’ planar near-field scanner. The AAMTV provides phase trimming and a small amount of delay using electrical components while the WOMBAt provides longer delays using commercial-off-the-shelf (COTS) optical components typically manufactured for the telecommunication industry. By integrating the WOMBAt with the AAMTV, a highly flexible test environment was achieved that includes system calibration, multi-frequency scanning, and antenna pattern analysis. Phase I receive tests for this system were previously described and presented to AMTA[1] in 2002. This paper will describe the results of reconfiguring the AAMTV into a transmit architecture for Phase II. WOMBAt successfully demonstrated wideband TTD in both receive and transmit configurations at angles greater than the system goal of ±65º while exceeding all other system level performance goals. System level performance included a beam squint of less than 1.1º for receive and 0.5º for transmit, a worse case amplitude variation of 2.4 dB receive and 1.6 dB transmit and differential delays of less than 3.5 picoseconds.

Measurement of the Earth-Observer-1 Satellite X-Band Phased Array
K. Perko (Goddard Space Flight Center ),J. Demas (Near-Field Systems), L. Dod (Swales Aerospace ), November 2003

The recent launch and successful orbiting of the EO-1 Satellite has provided an opportunity to validate the performance of a newly developed X-Band transmitonly phased array aboard the satellite. This paper will compare results of planar near-field testing before and after spacecraft installation as well as on-orbit pattern characterization. The transmit-only array is used as a high data rate antenna for relaying scientific data from the satellite to earth stations. The antenna contains distributed solid-state amplifiers behind each antenna element that cannot be monitored except for radiation pattern measurements. A unique portable planar near-field scanner allows both radiation pattern measurements and also diagnostics of array aperture distribution before and after environmental testing over the ground-integration and pre-launch testing of the satellite. The antenna beam scanning software was confirmed from actual pattern measurements of the scanned beam positions during the spacecraft assembly testing. The scanned radiation patterns on-orbit were compared to the near-field patterns made before launch to confirm the antenna performance. The near-field measurement scanner has provided a versatile testing method for satellite high gain data-link antennas.

Aspects of Antenna Pattern Characterization of an L-Band Space Radiometer
S. Pivnenko (Technical University of Denmark),J.M. Nielsen (Technical University of Denmark), O. Breinbjerg (Technical University of Denmark), November 2003

This paper deals with different aspects of the on-ground antenna pattern characterization of the MIRAS radiometer for ESA’s SMOS mission. Various technical challenges of the project are briefly described. Special attention is given to the effect of multiple reflections between the antenna under test and the measurement probe. A series of antenna measurements of the MIRAS radiometer antennas is now on-going at the DTU-ESA Facility. The main objectives of these are to investigate the accuracy of the forthcoming antenna characterization, to find solutions to the already known problems, to identify new possible difficulties, and to establish an optimal measurement strategy, which should allow for the tight error requirements and minimize the overall time of the measurement campaign.

A Design Framework for Integrated Modeling of Spacecraft Antenna
A. Guidoni (IDS Ingegneria Dei Sistemi SpA),L. Benvenuti (IDS Ingegneria Dei Sistemi SpA), L. Pandolfo (IDS Ingegneria Dei Sistemi SpA), M. Sabbadini (ESA-ESTEC), R. Guidi (IDS Ingegneria Dei Sistemi SpA), November 2003

As known, spacecraft antenna design is an everdemanding task, due to the tight requirements on performance and the small available space. Moreover, the trend of installing array antennas onboard makes this task even more complex. For this reason, every antenna design must be verified against its installation constraints, in term of pattern distortion, due to interaction with spacecraft structure, inter-antenna coupling with nearby antennas, which can be remarkable due to the reduced available space, and generation and propagation of passive inter-modulation products (PIM), that can seriously affect the performance of transponders. For the above reasons, a Design Framework has been developed in the frame of an ESA contract. In this activity, European universities, industry and research centers cooperated in order to integrate within a single environment different prediction codes providing the required modeling capabilities. The system is able to guide the user from the antenna design phases through antenna installation simulation. The framework also allows for storage and management of experimental data in the more common formats or in user-defined ones, making able the designer to validate its numerical models with measured data obtained from intermediate breadboards. A validation activity is in progress and comparisons between simulation and measurements are reported, together with main characteristics of the design system. The system has been applied, among others, in the design and compatibility analysis, of Galileo antennas.

Antenna Pattern Measurement of Microstrip Antennas Using Photonic Sensor and Spherical Scanning Techniques
M. Hirose (National Metrology Institute of Japan, AIST),J. Komiyama (National Metrology Institute of Japan, AIST), T. Ishizone (Toyo University), November 2003

We have developed the spherical near-field measurement system using a photonic sensor as the probe of the spherical scanning. Because the photonic sensor is a few gram of weight and a few mm in length, the measurement system can be compact and simple. The probe compensation is not needed because the photonic sensor can be considered as an ideal infinitesimal electric dipole antenna in the spherical near-field measurements as well as the planar near-field measurements as shown before. To demonstrate the validity of the system, we have measured the antenna patterns of a microstrip antenna on a finite printed board at 5.85 GHz. The measurements by the photonic sensor agreed with the one by the far-field method.

Interactions Between Probe Arrays and Antenna Under Test in Cylindrical and Spherical Near-Field Test Ranges: Numerical Assessment and Compensation Schemes
A. Ziyyat (Mohammed first University),D. Picard (Supélec), J-Ch Bolomey (Supélec), November 2003

While probe arrays are now recognized to allow rapid and accurate near-field measurements, the interaction with the Antenna Under Test (AUT) is still sometimes considered as a potential limitation, especially for electrically large directive antennas [1]. Based on numerical simulations, this paper reports the results of a thorough investigation of the interaction mechanism and analyses its impact on the far-field pattern accuracy. The most often, interaction effects can be maintained at an acceptable level, thanks to an appropriate design of the probe array element and structure. However, the efficiency of a posteriori compensation schemes has also been investigated. The Pattern Coherent Averaging Technique (PCAT) [2], which is well known for compensating plane wave deviations in the quiet zone of antenna far-field test ranges or interactions from single probe near-field facilities, also proved very efficient to reduce the interaction effects with a probe array.

Test and Assessment of a Direction Finding Antenna Measured on the Nose of an MH-47A Helicopter
S. Abbott (US Army), November 2003

One basic Direction Finding (DF) technique for Radar is Amplitude Based Comparison DF. Multiple directional antennas are placed around an aircraft to get a 360 deg view of the area. By placing these antennas on the aircraft, the antennas are subjected to reflections from the aircraft, which distorts the antenna characteristics. This antenna distortion causes errors in the measurement of the angle of arrival. The work presented here describes the measurement of the antenna characteristics of a cavity backed spiral antenna both by itself and attached to the nose of an MH- 47A helicopter nose measured in an anechoic chamber. The spiral antenna’s pattern was changed when it was measured on the helicopter. The effect this change in pattern has on the DF accuracy is discussed.

Validation of a Compact Antenna Range for Broad Beam Antennas
R.C. Schulze (John Hopkins University),J. Tanzman (John Hopkins University), B. A. Baertlein (The Ohio State University), W.D. Burnside (The Ohio State University), W.H. Theunissen (The Ohio State University), November 2002

A compact range was recently constructed at the Applied Physics Laboratory to measure broad-beam, fan-beam, and pencil-beam antennas (max aperture: 1 meters). Chebyshev absorber treatments, lightweight composite reflector, foam column mount for light-weight antennas, automated measurement software, and a novel feed spillover rejection algorithm are the technology elements implemented in this compact range measurement facility. This paper will describe a trade study that APL performed before the compact range antenna facility was built. Solutions to some of problems that were encountered during the construction will be discussed as well as the overall performance of the facility. The measurement of a broad-beam antenna will be compared to calculated pattern. This measurement will highlight the advantages of using a software range gate that was recently developed.

Correcting Dual Port Probe's Port-to-Port Calibration Using Near-Field Measurements
A.C. Newell (Newell Near-Field Consultants),J. Way (TRW Space and Electronics Group), November 2002

When a dual port probe is used for near-field measurements, the amplitude and phase difference between the two ports must be measured and applied to the probe correction files so that the measurements and calculations will have the same reference. For dual port linear probes, the measurement of this “Port-to-Port” ratio is usually accomplished during the gain or pattern measurements by using a rotating linear source antenna.1 When a dual port linear probe is used to measure a circularly polarized antenna, the uncertainty in this Port-to-Port ratio can have a significant effect on the determination of the cross polarized pattern. Uncertainties of tenths of a dB in amplitude or 1-3 degrees phase can cause changes in the cross polarized pattern of 5-10 dB.2 3 The paper will present a method for measuring the Port-to-Port ratio on the near-field range using a circularly polarized antenna as the AUT (Antenna Under Test). The AUT does not need to be perfectly polarized nor do we need to know its correct polarization. The measurements consist of two separate near-field scans. In the first measurement the probe is in its normal position and in the second it is rotated about the Z-axis by 90 degrees. A script then calculates the Port-to-Port ratio by comparing the crosspolarization results from the two measurements. Uncertainties in the Port-to-Port ratio can be reduced to hundredths of a dB in amplitude and tenths of a degree in phase. Measurements were taken at TRW’s Large Horizontal Near-field Antenna Test Range.

Measured Frequency Performance of a X-Band 4-Port Butler Matrix on a Planar Near-Field Range
J. Kemp (Georgia Tech Research Institute),G. Hampton (Georgia Tech Research Institute), November 2002

Single-beam and composite-beam performance of a 4-port X-band waveguide Butler matrix was measured on the Georgia Tech Research Institute planar near-field range for wideband frequency performance. The techniques necessary to perform accurate measurements on a broad-beamed antenna in a near-field range will be discussed, and measured far-field pattern data collected at the design frequency of 9.3 GHz are presented and compared with predicted results of the Butler matrix. In cases where the measured data and the expected results do not compare well, aperture amplitude and phase data, transformed from the near-field data, are shown as a diagnostic tool for corrections. After correction, new data at 9.3 GHz are presented for comparison with predicted results, and selected farfield pattern data collected at 8.6 GHz and 11.0 GHz are presented.







help@amta.org
2024 Antenna Measurement Techniques Association. All Rights Reserved.
AMTA_logo_115x115.png
 
 

CONNECT WITH US


Calendar

S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30