Welcome to the AMTA paper archive. Select a category, publication date or search by author.
(Note: Papers will always be listed by categories. To see ALL of the papers meeting your search criteria select the "AMTA Paper Archive" category after performing your search.)
The following features have been added to the spherical near-field software set which is available for the Scientific-Atlanta 2022A Antenna Analyzer. Gain Comparison Measurement Probe Pattern Measurement and Correction Thermal Drift Correction Spherical Modal Coefficient Analysis Far-Field, Radiation Intensity, and Polarization Display The addition of the probe pattern correction permits antenna measurements to be made at range lengths down to within several wavelengths of touching. The addition of probe polarization measurement permits three antenna polarization measurements to be made and analyzed as well as two antenna polarization transfer measurements. Correction for phase and amplitude errors attributable to thermal drift is accomplished by the return-to-peak method. Reduction of antenna patterns to spherical modal coefficients is an essential feature of spherical near-field to far-field transforms and is offered as an augmentation to antenna design. Far field display features permit the far fields of antennas to be presented in both component and radiation intensity formats, in circular, linear and canted linear polarization components.
This presentation will focus on the recently revised ANSI C95 RF Radiation Exposure Standard. Some of the research background for the new standard will be given, and its impact will be explained. Instrumentation guidelines for measuring potentially hazardous fields will be presented. The possible damaging effects of non-ionizing RF radiation is receiving increased attention in the public eye, and it behooves the practicing antenna engineer to be aware of the potential dangers to health and safety from exposure of RF energy.
The following features have been added to the spherical near-field software set which is available for the Scientific-Atlanta 2022A Antenna Analyzer. Gain Comparison Measurement Probe Pattern Measurement and Correction Thermal Drift Correction Spherical Modal Coefficient Analysis Far-Field, Radiation Intensity, and Polarization Display The addition of the probe pattern correction permits antenna measurements to be made at range lengths down to within several wavelengths of touching. The addition of probe polarization measurement permits three antenna polarization measurements to be made and analyzed as well as two antenna polarization transfer measurements. Correction for phase and amplitude errors attributable to thermal drift is accomplished by the return-to-peak method. Reduction of antenna patterns to spherical modal coefficients is an essential feature of spherical near-field to far-field transforms and is offered as an augmentation to antenna design. Far field display features permit the far fields of antennas to be presented in both component and radiation intensity formats, in circular, linear and canted linear polarization components.
In order to accurately determine the far-field of an antenna from near-field measurements the receiving pattern of the probe must be known so that the probe correction can be performed. When the antenna to be tested is circularly polarized, the measurements are more accurate and efficient if circularly polarized probes are used. Further efficiency is obtained if one probe is dual polarized to allow for simultaneous measurements of both components. A procedure used by the National Bureau of Standards for determining the plane-wave receiving parameters of a dual-mode, circularly polarized probe is described herein. First, the on-axis gain of the probe is determined using the three antenna extrapolation technique. Second, the on-axis axial ratios and port-to-port comparison ratios are determined for both the probe and source antenna using a rotating linear horn. Far-field pattern measurements of both amplitude and phase are then made for both the main and cross components. In the computer processing of the data, the on-axis results are used to correct for the non-ideal source antenna polarization, scale the receiving coefficients, and correct for some measurement errors. The plane wave receiving parameters are determined at equally spaced intervals in k-space by interpolation of the corrected pattern data.
When low crosspolar pattern measurements are required, as in the case of the L-SAT Propagation Package Antennas (PPA) with less than -36 dB linear crosspolarization inside the coverage zone, the use of good polarization standards is mandatory (1). Those are usually electroformed pyramidal horns that produce crosspolar levels over the test zone well below the -60 dB level typically produced by the reflectivity of anechoic chambers. In this case the alignment errors (elevation, azimuth and roll as shown in fig. 1) can become important and its efects on measured patterns need to be well understood.
An innovative technique has been developed for accurately measuring very low Sidelobe Antenna patterns by the method of planar near field probing. The technique relies on a new probe design which has a pattern null in the direction of the test antenna’s steered bean direction. Simulations of the near field measurement process using such a probe show that -60dB peak side-lobes will be accurately measured (within established bounds) when the calibrated near field dynamic range does not exceed 40 dB. The desireable property of the new probe is its ability to “spatially filter” the test antenna’s spectrum by reduced sensitivity to main beam ray paths. In this way, measurement errors which usually increase with decreasing near field signal level are minimized. The new probe is also theorized to have improved immunity to probe/array multipath and to probe-positioning errors. Plans to use the new probe on a modified planar scanner during tests with the AWACS array at the National Bureau of Standards will be outlined.
The radar scatter matrix can be accurately characterized in magnitude, relative phase, and polarization for both far-field monostatic and bistatic conditions by means of a microwave interferometer. A separate transmitting antenna illuminates the target of interest while two adjacent receiving antennas measure magnitude and the combine in a phase comparator whose output is a phase differential caused by a changing target aspect angle. Using correct constants and scale factors this differential is integrated to provide target phase information. Different polarizations are obtained by switchable feeds. The technique can be used on an RCS range under static conditions or under dynamic conditions with a ground based radar and an airborne target. The advantage gained is that errors due to radar path length changes are eliminated.
There is a growing interest, for developing large, high performance communication antennas for use in space. Such antennas employ many new technologies and are very expensive to design, build, and deploy. These high risk projects require thorough ground testing before becoming operational. Unfortunately, accurately measuring the far field pattern of a large, structurally weak, high performance antenna on the ground is a difficult problem. The antenna’s extraordinary characteristics place severe tolerances on an antenna measurement range. This paper examines many of the problems encountered with measuring the far field pattern of these antennas. Several possible techniques are reviewed and the errors, tolerances, and limitations associated with each technique are analyzed.
This paper presents the results of research conducted to compensate near field measurements for known errors in near field probe position. The complete solution for probe position error compensation and associated computer algorithm developed by Corey as a Ph.D. dissertation resulted in a large computer memory and computation time requirements. Corey’s results showed, however, that the prime effect of probe positioning error was a change in the near field measurement phase in the direction of main beam propagation. It was also shown that the sinusoidal components of the probe position error produced spurious sideband propagation directions in the calculated far field patterns. This information has been used to develop a simplified probe position error compensation technique which requires negligible computer storage and computation time. An early version of this technique has recently been implemented at RCA for the Aegis near field measurement facility. The technique and sample results are presented for a small probe position errors and for a low sidelobe level antenna measurement.
An instrument has been built which allows the electromagnetic measurement of the surface accuracy of a large millimeter-wavelength antenna. The University of Texas 4.9 m radio telescope has been measured with this technique at 86.1 GHz to an accuracy of 4 µm at the surface. Our technique is an interferometric one which is fast, accurate, and able to measure the whole antenna surface at once. While the technique is illustrated by its use on a large antenna, it could be used in a near field measurement of a smaller antenna. Several antenna surface maps are presented. A comparison of run-to-run repeatability was made. The technique itself was tested by deforming the antenna surface in a known way and subsequently detecting the deformation. In addition, important factors which influence the overall error budget have been identified. These include errors in setting the antenna angular position and fluctuation noise in the atmosphere and electronics. An instrument has been built which allows the electromagnetic measurement of the surface accuracy of a large millimeter-wavelength antenna. The University of Texas 4.9 m radio telescope has been measured with this technique at 86.1 GHz to an accuracy of 4 µm at the surface. Our technique is an interferometric one which is fast, accurate, and able to measure the whole antenna surface at once. While the technique is illustrated by its use on a large antenna, it could be used in a near field measurement of a smaller antenna. Several antenna surface maps are presented. A comparison of run-to-run repeatability was made. The technique itself was tested by deforming the antenna surface in a known way and subsequently detecting the deformation. In addition, important factors which influence the overall error budget have been identified. These include errors in setting the antenna angular position and fluctuation noise in the atmosphere and electronics.
Compact Antenna Ranges (C.R.) proved to suitable for indoor measurements of antennas of moderate size (up to about 4 feet) in the frequency ranges from 4-18 GHz. Where less accurate measurements are allowed, the upper frequency limit can be as high as 60 GHz in current C.R. design. Dimensions of such a range are approximately 4 times larger (in linear dimension) than those of the test antenna. This is due to the face that there is a considerable taper in the amplitude over the aperture of the C.R. Considerable improvements in the electrical performance may be expected for ranges in which two crossed parabolic cylindrical reflectors are used. Due to the increased focal length the uniformity of the amplitude distribution across the final aperture is increased considerably compared to conventional design. Furthermore, an asymmetrical plane-wave zone can be created which makes it possible to measure the patterns of asymmetrical antennas or devices including the direct environment (antennas on aircraft or spacecraft). A compact range which consists of a main reflector with overall dimensions of 2x2 metres has been used for experimental investigation in the 8-70 GHz frequency band. At 10 GHz the plane-wave zone has a slightly elliptical shape (100x90cm). The amplitude variations are in this case less than 0.3dB; the corresponding phase errors are less than 4 degrees. It has been shown that the reflectivity level can be kept below –60dB. Only a minor degradation in performance was found at 70 GHz. In conclusion, the performance of this new compact range is as good as, or better than that of most outdoor ranges. The upper frequency limit is about 100 GHz for ranges of moderate size (up to 3 metres). Summarizing, the main advantages compared to other compact ranges are: -Larger test zone area (up to 2x) for the same C.R. reflector size -better crosspolar performance -considerably higher upper frequency limit The last-named is due to the cylindrical reflector surfaces, which are easier and cheaper to manufacture than double-curved surfaces.
This paper describes a new, automated, microprocessor controlled, dual-channel microwave vector ratio measurement receiver for the frequency range 10 MHz to 18 GHz. It provides a greater than 120 dB dynamic range and resolutions of 0.001 dB and 0.1 degree. Primarily designed as an attenuator and Signal Generator Calibrator, it offers solutions to antenna measurement problems where high accuracies and/or wide dynamic measurement ranges are required such as for broadband cross-polarization measurements on radar tracking antennas, highly accurate gain measurements on low-loss reflector antennas, frequency domain characteristics measurements on wide-band antennas with resulting data suitable for on-line computer conversion to time domain transient response and dispersion characteristics data and wideband near field scanning measurements for computing far field performances. The measurement data in the instrument is obtained in digital form and available over an IEEE-488 bus interface to an outside computer. Measurement times are automatically optimized by the built-in microprocessor with respect to signal/noise ratio errors in response to the measurement signal level and the chosen resolution. Complete digital measurement data amplitude of both channels and phase, is updated every 5 milliseconds.